SUN® Purefexion Disinfectant Wipes, 160 Ct

Purefexion Wipes deliver powerful efficacy against pathogens—without the harmful, irritating effects of other chemical disinfectants—in an easy-to-use wipe. 

 

Features & Benefits 

Powerful disinfection—broad efficacy:
Kills 99.9% of household germs
Eliminates odor-causing bacteria
Sanitizes in as little as one minute
Low pH
Virucidal, germicidal, fungicidal and tuberculocidal efficacy
Effective against antibiotic-resistant organisms
Effective against Norovirus 

Non-irritating:
No quats or bleach
EPA category IV (lowest level of toxicity)
No precautionary statements/PPE
Will not irritate skin, eyes, or lungs
Highly biodegradable ingredients—no harmful or irritating residues 

One-step, no-rinse cleaning & disinfection:
Proven efficacy in the presence of 5% organic soil load
5-minute contact time for disinfection
No pre-cleaning or post-rinsing steps required

Certifications

EPA DfE-Certified Product-100% Biodegradable Substrate
OSHA requirements for bloodborne pathogens
HMIS ratings of “0”
EPA List N approved for use against SARS-CoV-2

 

Usage

For use on hard, non-porous surfaces, such as stainless steel, chrome, glass, plastic, and vinyl.

A two-step process of cleaning prior to disinfection is required only when surfaces are grossly soiled or there is the possibility of contamination with blood or body fluid. Purefexion Wipes can be used for both cleaning and disinfecting.

1. Always wear gloves when cleaning. These wipes are for cleaning surfaces, not for use on skin. Wear a cover gown and face protection in addition to gloves if cleaning up a large body fluid spill.

2. Pull cloth wipe from the container at 90° angle making certain to position the wipe between the two pointing arrows appearing on the lid. This permits easy separation of cloths at perforation.

3. Unfold cloth and wipe surfaces until visibly wet. Allow solution to air dry.

• Do not wipe the surface dry prior to adequate contact time. Wexford disinfectants contain humectants that evaporate slowly to prolong drying time. Although the surfaces may appear dry, there is still dampness or moisture present. This ensures complete bacteria kill.

4. Wipe or rinse any residual, after sufficient contact time, from shiny surfaces if needed.

5. Keep small center cap closed to prevent moisture loss from container.

 

Procedure for Cleaning and Disinfecting Using Wexford Purefexion Wipes on Equipment and Cords

1. Purefexion Wipes are for cleaning surfaces only, not for use on skin.

2. Pull cloth wipe from the container at 90° angle making certain to position the wipe between the two pointing arrows appearing on the lid. This permits easy separation of cloths at perforation.

3. Unfold cloth.

4. Start at the connectors and wet down but do not saturate the cables while wiping away from the connectors. It is sometimes necessary to wring out the towelettes to avoid excess fluid on the cables. Allow solution on cables to air dry.

5. Do not allow any solution from the towelettes to drip into the cord connectors.

6. If pooling occurs at the cord connectors, allow adequate contact time and then dry the connectors before reuse.

7. Cords and equipment should not be saturated.

8. Do not wipe the surface dry prior to adequate contact time.

9. Wipe or rinse any residual, after sufficient contact time, if needed

10. Allow cords to dry before packaging the equipment for reuse.

11. Keep small center cap closed to prevent moisture loss from container.

12. A two-step process of cleaning prior to disinfection is required only when surfaces are grossly soiled or there is the possibility of contamination with blood or body fluid. Wipes can be used for both cleaning and disinfecting. 

 

Ingredients 

Water, Sodium Octyl Sulfate, Lactic Acid, Malic Acid, Acetic Acid, Pelargonic Acid, Citric Acid, Sodium C14-16 Olefin Sulfonate, Ammonium C6-10-alkyl Polyoxyethylene Sulfate, C12-15 Alcohols Ethoxylated